Fume Hoods for Organic & Medicinal Synthesis

A planning guide for reaction setups, workups and solvent removal in research, teaching and drug-discovery labs: apparatus clearance, changing chemical lists, hood utilities and building exhaust.

Magnetic hot plate stirrer heating a flask beside laboratory glassware with a chemical fume hood behind the bench

Filtered Fume Hoods You Can Price Online

These are real Labs USA store listings for filtered (ductless) hoods. Most synthesis labs should start with a <strong>ducted</strong> chemical fume hood, which we quote to your room and building exhaust. A filtered hood is only worth reviewing for a small, fixed, low-volume task whose full chemical list the manufacturer has approved for its filter. It is not suited to a changing reaction inventory, heated reflux of large solvent volumes, or chemicals the filter cannot hold.

Why synthesis needs its own hood plan

Organic and medicinal chemistry labs use a fume hood differently from most other labs. One chemist may run a reflux overnight, take apart a quench the next morning, strip solvent on a rotary evaporator after lunch and run a flash column before leaving. The apparatus is tall, it is clamped to a frame, it is attached to water, vacuum and inert gas, and it often runs unattended. The chemical list also changes every week as new routes and new building blocks come in. A hood that suits a teaching bench or a fixed QC method can feel cramped or poorly served in this kind of work.

This page covers just that planning problem: how to size and lay out a hood around reaction apparatus, how to prepare for a changing chemical inventory, which utilities to bring to the hood, and what the building exhaust has to support. For hood families and general selection, start with our laboratory fume hoods overview. For general bench chemistry, see the chemistry hood page. For powder weighing and GMP pharmaceutical work, see pharmaceutical fume hoods.

This page does not give reaction procedures, and it does not replace your chemical hygiene plan, your safety data sheets or a ventilation engineer’s review. We do not publish universal face-velocity or exhaust-volume numbers, because those depend on the hood model, the sash configuration, the room and the building. Our goal is to help you start a quote with the right information already organized.

Map the synthesis work that will happen in the hood

Start by listing the operations, not just the chemicals. The table below covers common synthesis tasks and what each one means for the enclosure. Use it as a worksheet with your principal investigator or lab manager. The right-hand column lists the questions an equipment supplier and your EHS team will ask.

OperationWhat it needs from the hoodQuestions to answer before quoting
Reflux and heated reactionsVertical space for flask, condenser and adapters. Rigid support for clamps. Cooling water in and out. A heat source with its controls reachable outside the sash.Largest flask and condenser stack height? Overnight or unattended runs? Heating mantles, oil baths or aluminum blocks?
Inert-atmosphere work (Schlenk line, manifold, balloons)Gas and vacuum lines run inside the hood. Room for a manifold and cold traps. Tubing kept away from the sash track.House nitrogen or argon, or cylinders? House vacuum or a dedicated pump? Where will the pump and its exhaust sit?
Distillation and solvent purificationTall glass setups. Receivers and cold traps. Possibly a dedicated area for still pots or solvent purification columns.Atmospheric or vacuum distillation? Recurring solvent stills, or a purification system outside the hood?
Rotary evaporationFootprint for the evaporator, bath and chiller lines, plus a vacuum source. Bump traps and the condenser need vertical clearance.Will the rotovap live in the hood full time, or on a bench under local exhaust? Pump exhaust routing?
Workup, extraction and quenchingClear deck space for separatory funnels, ice baths and waste containers. Quenches can release gas and heat quickly.Typical batch volume? Reactive reagents (hydrides, organometallics, acid chlorides) that need staged quench space?
Flash chromatography and TLCWidth for a column or an automated system, fraction racks, solvent reservoirs and a UV lamp.Manual columns or an automated system? Where are solvent supply and waste carboys?
Recrystallization, filtration and dryingRoom for vacuum filtration flasks and funnels. Hot solvent handling. Sample transfer to a vacuum oven or desiccator.Is a vacuum oven or drying station nearby? Do wet solids leave the hood on a closed carrier?

Size the hood around the apparatus, not the floor plan

Synthesis hoods are usually limited by height and depth before they run out of width. A round-bottom flask on a lab jack, a reflux condenser, a drying tube or gas adapter and an addition funnel can easily stack above the sash opening if the hood is too shallow or the work surface sits too high. Measure your tallest routine setup with its jack and clamps, then compare it with the interior height and the clear sash opening of each hood you consider.

Depth matters for two reasons. It lets the apparatus sit well back from the sash plane, where capture is most reliable, and it leaves a working strip in front for funnels and notebooks. Ask your EHS group how far back your institution wants equipment kept, and confirm the manufacturer’s guidance for the specific model.

Wide chemical fume hood with a tall glass sash on steel base cabinets in a university laboratory

Width follows from the number of simultaneous setups. A useful rule of thumb when planning is to count how many apparatus stacks each chemist runs at once, and give each one its own section of frame. Do not plan to share one stack between two people. Crowding pushes glassware toward the sash and blocks the rear baffle slots, which disturbs airflow for everyone at that hood.

  • Support frame: plan a lattice or rod frame across the back or sides so clamps never hang from utilities or the sash.
  • Sash type: vertical sashes give full-height access for setting up tall apparatus. Combination sashes (horizontal panels inside a vertical frame) let a chemist work behind a panel during routine manipulations.
  • Raised equipment: place stir plates and baths on stands or jacks that leave air space beneath them. Do not set large items flat against the rear baffle.
  • Unattended runs: label overnight reactions, and decide where a run-alone setup goes so it does not block another chemist’s working space.

Plan for a changing chemical inventory

Technician releasing a visible fog test into the face of a chemical fume hood to show airflow capture

Synthesis labs add reagents and solvents constantly, and many of them are flammable, toxic, corrosive or reactive. Common examples are halogenated solvents such as dichloromethane, ethers such as THF and diethyl ether, and strong acids. They also include reactive organometallics, hydrides, coupling reagents, and new compounds whose hazards have not been fully characterized yet. Your hood choice has to cover the chemicals you will use next year, not just the ones on this month’s order.

This is the main reason most synthesis hoods are ducted. A ducted chemical fume hood exhausts contaminated air out of the building, so it does not depend on a filter matching each chemical.

ConsiderationDucted chemical fume hoodFiltered (ductless) hood
Changing reagent listSuitable, because it does not depend on a filter chemistry match.Every new chemical has to be reviewed against the filter. That rarely suits discovery chemistry.
Heated reflux and solvent strippingCommon use with the right utilities and sash practice.Large or continuous vapor loads can exceed filter capacity. Review with the manufacturer first.
Unknown or newly synthesized compoundsPreferred, because no filter capacity claim is needed.Generally not appropriate, because filter performance cannot be confirmed.
Building impactNeeds exhaust duct, a fan, make-up air and controls.No exhaust duct. Needs filter monitoring, replacement and a documented chemical list.
Where it can fitResearch labs, process labs and most organic teaching labs.Small, fixed, well-characterized tasks, such as weighing a known solvent or a recurring sample prep.

If a filtered hood is considered at all, the manufacturer should review the full chemical list, including workup, cleanup and waste solvents. Your EHS team should also agree to the filter monitoring and change program. The filtered hoods in our store are shown with that limitation in mind. They are not a general substitute for a ducted synthesis hood.

Bring the right utilities to the hood

Synthesis setups run on utilities. Plan the service fixtures with the chemists who will actually work at the hood. Then confirm what the building can supply.

  • Cooling water: supply and drain for condensers and rotovap coils, or a recirculating chiller to save water and reduce flood risk.
  • Vacuum: house vacuum or a local pump. Decide where pump exhaust goes, and whether cold traps are needed.
  • Inert gas: house nitrogen or argon, or cylinder regulators outside the hood with lines run inside.
  • Electrical: outlets on the hood exterior so plugs and controls stay outside the sash. Confirm ratings for heating mantles and controllers.
Fume hood side post with blue service fixture valve handles and a labeled service panel
Electrical power cord plugged into a duplex receptacle on the exterior post of a laboratory fume hood

Remote valve handles and exterior receptacles let a chemist shut off water, gas or power without reaching into the hood or past glassware. That matters most during an upset, when the sash should come down and the heat source should go off fast.

Plan cord and tubing routes so nothing crosses the sash track. A cord pinched under a sash prevents it from closing. Tubing draped over the airfoil also disturbs the air entering the hood.

Also ask about fixture count and placement before the hood is ordered. Fixtures are much easier to specify at the factory than to add in the field. Typical synthesis requests include two water fixtures (or one plus a chiller), vacuum, one or two gas fixtures and several exterior outlets. Your actual list should come from the apparatus inventory you built in the workflow table.

Airflow monitoring and sash habits

Every synthesis hood should have a working airflow monitor that the chemist can see from the working position. It should alarm when airflow falls outside the range set during commissioning. OSHA’s non-mandatory laboratory guidance says chemical hoods should be maintained, monitored and routinely tested for proper performance.

Sash height is the daily control that matters most. Work with the sash as low as practical, close it fully when no one is working at the hood, and keep it down over unattended reactions. If your building uses variable air volume controls, lowering the sash also reduces exhaust and conditioned-air use.

Chemist working at a chemical fume hood with an airflow monitor beside a partly lowered sash

Coordinate the hood with the building exhaust

A ducted synthesis hood is one part of a building system. The fan, ductwork, roof discharge, make-up air and room pressure all have to agree with it. Adding hoods or changing their mode affects the rest of the building. OSHA’s laboratory guidance notes that the effect on laboratory and hood ventilation should be considered before any building HVAC is modified.

Before you order, find out whether the hood will connect to an existing exhaust fan or need a new one. Ask who owns the airflow balance (often the mechanical contractor or a test-and-balance firm) and whether the room has the make-up air for one more hood.

White corrosion-resistant centrifugal exhaust blower used to pull air from a laboratory fume hood
QuestionWho usually answers itWhy it matters for synthesis
Constant volume or VAV exhaust?Facilities or the mechanical engineerDecides which hood controls and sash sensors are needed and how sash habits affect energy use.
Dedicated fan or manifolded system?Mechanical engineerAffects duct material, connections and what happens to the hood if a shared fan is serviced.
Duct material and routeMechanical engineer and EHSHalogenated solvents, acids and condensing vapors influence the duct material and drainage choices.
Room make-up air and pressureMechanical engineerWithout enough supply air the hood cannot pull its design airflow, and doors can become hard to open.
Commissioning and testingEHS with the installer or a certifierConfirms the installed hood performs to your institution’s criteria before chemistry starts.

Work surfaces, spill control and storage

A dished work surface keeps spills from a dropped flask or an overflowing bath inside the hood. Epoxy resin surfaces are a common choice for organic solvents and many acids. Confirm compatibility for your specific chemistry and cleaning agents with the manufacturer. A cup sink inside the hood can drain a condenser, but it adds a path for spills into the drain system. Decide with EHS whether you want one.

Black dished laboratory fume hood work surface with a raised containment edge and cup sink cutout
University chemistry lab with yellow flammable storage cabinets under a fume hood and an eyewash station nearby

Base cabinets under the hood are the usual home for daily-use solvents and corrosives. Use flammable-rated cabinets for solvents and vented or acid cabinets where needed. OSHA’s laboratory guidance states that chemicals should not be stored in the chemical hood itself, and that toxic or corrosive chemicals that need vented storage belong in vented cabinets instead.

Also keep chemical waste moving. The same guidance says waste should not be disposed of by evaporation in a hood. Plan a labeled waste station close to the hood and away from the working zone.

Extra planning points for medicinal chemistry

Medicinal chemistry adds two pressures to an ordinary synthesis lab. The first is throughput: parallel synthesis blocks, microwave reactors, automated purification and many small vials mean more equipment per chemist. The second is compound potency: some intermediates and final compounds are biologically active at very small doses, and their hazards may not be known yet.

  • Count equipment, not just chemists. A parallel reactor and an automated flash system can each take a hood section.
  • Weighing potent or dusty solids is often done in a ventilated balance enclosure or a powder containment hood, not on the open floor of a synthesis hood, where airflow can disturb the balance and spread powder. See our powder containment hoods for that task.
  • Decide in advance how new compounds will be handled until their hazards are known. Many institutions treat them as potentially hazardous and keep them in the hood.
  • Plan sample transfer and storage, such as sealed vials, a ventilated cabinet or a cold-storage location, so material does not sit on open benches between steps.
  • If the lab works under GMP or produces material for clinical use, the documentation and room requirements change. Review those with your quality team; this page covers research synthesis.

Related project: Northern Illinois University chemistry lab

Labs USA supplied twelve ceiling-mounted Nederman exhaust arms for a teaching chemistry lab at Northern Illinois University in DeKalb, Illinois. Our CRM records this order as Closed Won for a college chemistry lab. The NIU project page describes the arms and why they were mounted from the ceiling.

White ceiling-mounted articulated exhaust arm with a clear capture hood over a black chemistry lab bench

We include it as related context only. The NIU order was source-capture snorkels for a teaching lab. It did not include a fume hood, it does not document organic or medicinal synthesis, and we make no claim about the reactions run there, the installation, or measured performance. What it does show is one planning point that also applies here: local exhaust at the bench and enclosed hoods do different jobs. Snorkels capture small, open bench operations. Reflux, distillation and work with hazardous or unknown compounds belong in an enclosed chemical fume hood.

Information to gather before requesting a quote

Operation list

Reflux, distillation, rotovap, chromatography, quench and filtration tasks, with how many run at once.

Tallest setup

Height of your largest routine apparatus stack, including the lab jack, condenser and adapters.

Chemical families

Solvents, acids, reactive reagents and any potent compounds, with SDS documents for the main ones.

Utilities

Water or chiller, vacuum, inert gas and electrical loads per hood, plus where pumps will sit.

Building exhaust

Existing fan or new, constant volume or VAV, roof access, and who balances the system.

Room and storage

Room dimensions, door swing, under-hood cabinet needs, eyewash and shower locations, and waste station.

Related planning resources: solvent extraction and sample prep hoods, polymer and resin preparation hoods, and walk-in fume hoods for pilot-scale or floor-mounted apparatus.

When a synthesis is followed by solvent-based purification, review collector access, open vessels and waste routing with our guide to fume hoods for chromatography fraction handling. Assess this as a separate workflow, not automatic approval to share the same enclosure.

When a synthesis workup includes solvent concentration, plan condenser height, flask access and vacuum-pump exhaust separately with our guide to rotary evaporation and solvent-removal hood planning. Review the exact apparatus, chemicals and exhaust requirements before selecting or sharing an enclosure.

Request a quote for your synthesis fume hood

Tell us about your operations, your tallest setup, utilities and the room. Labs USA can help compare hood widths, sash types, fixtures, work surfaces and storage for review with your EHS and facilities teams. Please do not send confidential structures or routes; chemical families and SDS documents are enough to start.

    Synthesis fume hoods: frequently asked questions

    What size fume hood do I need for organic synthesis?
    Size it from your apparatus and how many setups run at once. Check the tallest routine stack against the interior height and sash opening, and give each simultaneous setup its own section of frame. Many research chemists find one person per hood, with a wide enough hood for two setups, a practical starting point. Your institution may have its own standard.
    Can I use a ductless hood for synthesis?
    Usually not as the main synthesis hood. Changing reagent lists, heated solvent work and unknown new compounds are hard to match to a filter. A filtered hood may be reviewed for a small, fixed task with a manufacturer-approved chemical list and a filter monitoring program.
    Should the rotary evaporator sit inside the hood?
    Many labs keep it in the hood or under local exhaust because solvent vapor and pump exhaust need control. It takes significant floor space, so plan for it when sizing. Wherever it sits, route the vacuum pump exhaust so vapors are not released into the room.
    Which service fixtures should a synthesis hood have?
    Most include cooling water or a chiller connection, vacuum, inert gas and exterior electrical outlets with remote controls. Build the list from your apparatus inventory, and order fixtures from the factory where possible.
    Can reagents be stored in the hood?
    No. OSHA’s laboratory guidance says chemicals should not be stored in the chemical hood. Use flammable, acid or vented cabinets below or near the hood, and keep only what the current operation needs on the work surface.
    Is this different from a general chemistry hood?
    The hood families are the same, but the planning priorities are different. Synthesis hoods need more height and depth for apparatus, more utilities, and readiness for a changing inventory. See our chemistry hood page for broader bench chemistry selection.
    Who sets the face velocity or exhaust volume?
    Your institution’s EHS group and the mechanical engineer, based on the hood model, the standard your institution follows and the building system. The installed hood should be tested at commissioning against those criteria.

    Sources and related resources

    Technical reference reviewed for this guide: OSHA 29 CFR 1910.1450 Appendix A (non-mandatory laboratory guidance on hoods, chemical storage, waste and HVAC changes). Final requirements must come from your chemical hygiene plan, your EHS team and the hood manufacturer for your exact chemistry, hood and building.

    Related Labs USA pages: laboratory fume hoods, chemistry hoods, pharmaceutical fume hoods and ductless fume hoods.

    Plan your synthesis hood around the apparatus you actually run

    Share your operations and utilities and we will help organize the options.