Fume Hoods for Chromatography Fraction Handling

A planning guide for packing columns, collecting and pooling solvent fractions, running TLC checks and handling chromatography waste inside a chemical fume hood.

Glass chromatography column dripping solvent fractions into a test tube rack inside a chemical fume hood

Filtered Fume Hoods You Can Price Online

These are real Labs USA store listings for filtered (ductless) fume hoods. Filtered hoods have real limits for chromatography: mixed solvent systems, halogenated solvents such as dichloromethane, larger daily volumes and frequently changing methods can exceed what a carbon filter is rated to retain, and a saturated filter can let vapor pass without obvious warning. They are shown for small, well-characterized tasks that the manufacturer has reviewed against your full solvent list. Most flash and preparative column work is planned around a ducted chemical fume hood, which we quote to your room.

Why fraction handling needs its own hood plan

Chromatographic purification is one of the most common daily tasks in synthetic, natural-product and teaching chemistry labs, and much of the vapor exposure happens away from the column itself. A typical run involves weighing and slurrying silica, packing a column, loading the sample, running several hundred milliliters to a few liters of solvent through it, collecting dozens of tubes, spotting and developing TLC plates, pooling the good fractions into a flask, and then disposing of mixed solvent and spent silica. Every one of those steps leaves open solvent surfaces in front of the user.

This page focuses on that fraction-handling workload: where the column, collection rack, pooling flask, TLC chamber and waste containers sit inside the hood, how much room the work really needs, and what to settle with your environmental health and safety (EHS) team before you choose a hood. For an overview of every hood family we supply, start with our laboratory fume hoods page. For broader bench-chemistry selection, see our chemistry hood page.

It is not a guide to choosing a chromatography instrument, column chemistry or water purification system. The hood decisions below apply whether fractions are collected by hand from a glass column or by an automated flash system with a fraction collector.

The fraction-handling workflow, step by step

Smoke demonstration showing vapor being drawn into the face of a chemical fume hood

Containment starts at the face. A fume hood protects the user only when vapors released inside it are drawn back and exhausted. Smoke demonstrations like this one show how air moves at the sash opening. In fraction work, the sources are spread across the work surface: the column outlet, a row of open tubes, the pooling flask and the TLC chamber.

Calibration and reagent treatment before instrument analysis need a separate workflow review from fraction collection. Use our fume hood guide for analytical standards preparation and derivatization to plan small-volume transfers, reagent compatibility and filter or ducting requirements.

Planning the hood around those sources, rather than around the column alone, is the main idea of this guide. Keeping every open container well behind the sash plane is the habit that makes the layout work.

StepWhat is releasedHood planning note
Weighing and slurrying silicaFine silica dust and solvent vapor as the slurry is mixedWeigh dry silica inside the hood or a vented balance enclosure; keep the slurry beaker well back from the sash.
Packing and loading the columnSolvent vapor from the reservoir and the open top of the columnAllow vertical clearance for the column, reservoir or pressure head; confirm the sash can sit at its working height without striking glassware.
Eluting and collectingVapor from every open tube in the rack, plus drips and splashesSize the interior so the rack sits at least six inches inside the face, never on the sill.
TLC checksVapor from the developing chamber, spotting capillaries and drying platesReserve a small zone for the chamber and plate drying; keep a UV viewing lamp outside or beside the hood if space is tight.
Pooling fractionsVapor as many tubes are emptied into one flaskPool directly inside the hood; plan where the flask sits before moving to rotary evaporation.
Waste and cleanupMixed solvent, contaminated silica and rinse solventKeep closed, labeled waste containers nearby and decide where spent silica dries or is bagged.

Solvents and hazards to put on your chemical list

The hood type, filter options and work surface all depend on the actual solvent list. Normal-phase flash chromatography commonly uses hexanes or heptane with ethyl acetate, dichloromethane with methanol, or other mixtures, and reversed-phase methods add water with methanol or acetonitrile. Many of these are highly flammable, some are toxic by inhalation, and dichloromethane is regulated by OSHA under its own standard. Each method also changes over time as gradients and solvent pairs are tuned.

Write the list as it will really be used: each solvent, the largest container that will be open at once, approximate liters per day, and any additives such as triethylamine, acetic acid or ammonia. Include TLC stains and dips, which can contain strong acids or oxidizers. That list is what a manufacturer and your EHS team need to evaluate hood construction, liner materials and any filtered option.

Plan for drips and spills. Fraction collection produces constant small drips from the column tip and from moving tubes. A dished work surface with a raised edge helps keep liquids inside the hood instead of running onto the sill or floor.

Choose surface and liner materials after reviewing your solvents and cleaning agents. Epoxy resin and other chemical-resistant surfaces perform differently with specific chemicals; ask for the manufacturer’s chemical-resistance data rather than relying on a general claim.

Dished black chemical-resistant fume hood work surface with a raised edge

Flammability

Most eluents are flammable. Keep ignition sources such as hot plates and non-rated electrical equipment out of the vapor zone, and confirm electrical requirements with your EHS team.

Pressure

Flash columns run under air or nitrogen pressure. Use glassware rated for that service, consider a safety shield, and leave room to work beside the column rather than reaching over it.

Silica dust

Dry silica gel is a fine powder. Weighing and pouring it in the hood keeps dust away from the breathing zone; spent silica still holds solvent and should be handled as waste.

Halogenated solvents

Dichloromethane and chloroform need separate waste streams in most labs and deserve particular care if a filtered hood is under consideration.

Ducted or filtered: an honest comparison for chromatography

A ducted chemical fume hood exhausts air outside the building through a dedicated system. It does not depend on a filter matching each solvent, so it handles changing methods and mixed solvent systems more flexibly. It does need exhaust capacity, ductwork, a roof or wall termination and makeup air, which makes installation a facilities project.

A filtered, or ductless, hood draws air through filters and returns it to the room. It can make sense for a small, well-defined task where the solvents and volumes are known and the manufacturer has confirmed filter compatibility. The limitations matter more for chromatography than for many other tasks: filters have finite capacity, solvent mixtures load them in ways that are hard to predict, some low-boiling and halogenated solvents are poorly retained, and the unit needs a filter-change schedule and monitoring. A filtered hood is not a substitute for a ducted hood when a method calls for several liters of solvent a day or new solvent systems are added regularly.

QuestionDucted chemical fume hoodFiltered (ductless) hood
Changing methods and solvent pairsFlexible; no filter matchingEach new solvent must be reviewed against the filter
Daily solvent volumeSuited to routine flash and preparative workBest limited to small, defined volumes the manufacturer approves
Halogenated solvents such as dichloromethaneHandled by exhaust; still needs EHS reviewAsk the manufacturer specifically; often a reason to go ducted
InstallationNeeds exhaust, ductwork and makeup airNeeds power and room space; no building exhaust connection
Ongoing cost and upkeepBuilding energy and periodic testingFilter replacement, monitoring and periodic testing
Room airAir leaves the buildingFiltered air returns to the room; filter breakthrough is the key risk

Our store lists several filtered hoods because they are the right fit for some labs. If your chromatography work is routine, varied or high-volume, plan for a ducted hood and let us quote it to your room and exhaust conditions.

Interior space, sash height and clearances

Researcher working at a bench-mounted chemical fume hood with the sash partly lowered

Work behind the sash, not at it. OSHA laboratory guidance recommends keeping work at least six inches inside the hood and the sash as low as practical. With fraction work, that means the rack, the pooling flask and the TLC chamber all need room behind that line, alongside the column stand.

Before choosing a width, lay out the actual equipment on a bench and measure the footprint, including room for your hands and for swapping tubes or racks.

Most labs that run columns daily find that a single narrow hood becomes crowded quickly. A wider hood, or two hoods side by side for two users, keeps the rack and the column on separate sides and leaves space for the TLC chamber. A common rule of thumb in chemistry-lab design is roughly two and a half linear feet of hood per person when hoods are the primary workspace, but your own workload and EHS guidance should drive the final number.

  • Vertical clearance: measure the column, reservoir and clamp stand at their tallest, and confirm they fit with the sash at its working height.
  • Collector footprint: automated flash systems and fraction collectors need bench depth, a level surface and space for rack changes. Check whether the system sits inside the hood or beside it with only the collection area ventilated.
  • Tubing and cable routes: plan how solvent lines, pressure lines and power cords pass so they do not hold the sash open or trip across the sill. Service fittings and electrical outlets should be reviewed for location and type.
  • Airflow obstructions: large equipment placed directly on the work surface can block the rear baffle slots. Raising bulky items slightly on blocks, where the manufacturer allows, helps air pass underneath.
  • Two-person work: if two chemists share a hood, plan separate zones rather than crowding both setups into the center.

Services, monitoring and the room

Services inside the hood. Compressed air or nitrogen for flash pressure, vacuum for filtration, and electrical outlets for stirrers or a collector all need a planned location. Fixtures mounted on the hood posts, as shown here, keep controls outside the work zone.

Confirm gas types, vacuum, and outlet ratings with your facilities team early, because those choices affect how the hood is ordered.

Bench-top chemical fume hood with service fixtures and an electrical outlet beside the sash
Digital fume hood airflow monitor display mounted beside a hood sash

Airflow monitoring. A face-velocity or airflow monitor gives users a visible indication that the hood is operating, and an alarm when it is not. For long unattended collection runs, ask how the alarm will be noticed and who responds.

Set the operating criteria, sash height and verification method with your EHS team and the manufacturer. We do not publish a single face-velocity number because the right value depends on the hood, the room and the exhaust system.

The room matters as much as the hood. Supply air diffusers blowing across the hood face, doors that open next to the sash and heavy foot traffic can all disturb containment. A layout review should also cover where solvent supply bottles are stored, where pooled fractions go next for rotary evaporation, and whether the rotary evaporator itself needs ventilation.

Storage under and beside the hood

Flammable storage base cabinet with a warning label beneath a fume hood

Keep supply out of the hood interior. OSHA guidance recommends against using a chemical fume hood for storage. Containers left inside add to the vapor load and block airflow. A flammable base cabinet below the hood can hold the day’s eluent supply in its original containers.

Size base cabinets to daily needs and keep bulk solvent in your building’s designated storage. Fire code limits and cabinet types should be confirmed with your EHS team and local authority.

Waste, pooling and cleanup

Chromatography produces more waste than many lab tasks: unused fractions, mixed eluent, rinse solvent, spent silica and used TLC plates. Planning where that waste lives during a run keeps open containers to a minimum.

  • Separate streams: most programs separate halogenated from non-halogenated solvent waste. Label each container before the run.
  • Keep waste closed: use containers with funnels or caps that close between additions rather than open beakers. Safety waste cans and funnel systems designed for solvent collection can help.
  • Spent silica: decide whether columns drain in the hood before disposal and where contaminated silica is bagged and labeled.
  • Pool in place: combine fractions inside the hood and cap the flask before moving it to the rotary evaporator.
  • Cleanup: rinse glassware in the hood, then wipe the work surface. Plan a sink or rinse location if your program allows aqueous rinses.

Plan the whole room, not one hood. In labs where several chemists run columns, waste collection points, base-cabinet storage and the path to the rotary evaporator should be laid out with the row of hoods.

That keeps pooled fractions and waste from being carried across the lab in open containers.

Bench-mounted chemical fume hood with a vertical rising sash and perforated rear baffle

Related project: chemistry lab exhaust snorkels at NIU

Northern Illinois University ordered ceiling-mounted Nederman exhaust snorkels from Labs USA for a college chemistry lab. That order (verified as Closed Won in our CRM) shows the kind of chemistry teaching and research spaces we support.

It is related context only. It was a snorkel order, not a fume hood supply, and we do not have records describing chromatography work or fraction handling in that lab, so we make no claims about the lab’s methods or performance. See the NIU project page for the project details.

Ceiling-mounted exhaust snorkel arm above a laboratory bench

Information to gather before requesting a quote

  • Methods: manual glass columns, automated flash, preparative HPLC collection or a mix, and how often each runs.
  • Solvents: every eluent, additive and TLC stain, with the largest open volume and approximate liters per day.
  • Equipment: column heights, collector or rack dimensions, TLC chamber size, stirrers and any instrument that must sit inside.
  • Users: how many people work at the hood at once and for how long.
  • Services: nitrogen or air, vacuum, water and electrical needs.
  • Room and building: ceiling height, exhaust availability, room dimensions and photos.
  • Storage and waste: daily supply volume, waste streams and where pooled fractions go next.
  • Review team: who in EHS and facilities approves the hood type and testing plan.

With that information, we can recommend hood widths and types, work surfaces, base cabinets and accessories, and identify the decisions your EHS team or engineer needs to make. If your lab also runs extractions or sample preparation with solvents, compare our solvent extraction and sample prep guide.

Common planning mistakes in chromatography labs

Sizing for the column only

The rack, pooling flask, TLC chamber and waste need room too. Crowding pushes open tubes toward the sash.

Forgetting vertical clearance

Tall columns and reservoirs can force the sash higher than intended.

Choosing a filter without the full list

Mixed and halogenated solvents must be reviewed against the filter before a ductless hood is ordered.

Storing eluent in the hood

Supply bottles add vapor and block airflow. Use base cabinets and designated storage.

Pooling on the open bench

Pouring many tubes into one flask releases vapor. Pool inside the hood.

No plan for spent silica

Solvent-wet silica keeps releasing vapor. Decide where it drains and how it is packaged.

Before the purification stage, plan the reaction apparatus and work zone with our guide to fume hoods for organic and medicinal synthesis. Assess this as a separate workflow, not automatic approval to share the same enclosure.

Request a quote for your chromatography fume hood

Tell us about your methods, solvents, equipment and room. Labs USA can help compare ducted and filtered options, hood widths, work surfaces and storage for review with your EHS and facilities teams. Please do not send confidential compound information; solvent lists and equipment dimensions are enough to start.

    Chromatography fraction handling hoods: frequently asked questions

    Can I run flash chromatography in a ductless fume hood?
    Sometimes, for small and well-characterized tasks, but only after the manufacturer reviews every solvent, additive and volume against the filter. Mixed solvent systems, halogenated solvents and frequently changing methods are common reasons labs choose a ducted chemical fume hood instead.
    How wide should a fume hood for column chromatography be?
    Width follows the equipment and the number of users. Lay out the column stand, collection rack, TLC chamber and pooling flask, add working room behind the sash, and compare that footprint with available hood widths. We can help translate a sketch into options.
    Does an automated flash system with a fraction collector need to go in a hood?
    It depends on the system, solvents and your EHS program. Many labs ventilate the collection area because fractions sit open. Review the manufacturer’s installation guidance and your exposure assessment, and plan the bench depth either way.
    What face velocity should my hood run at?
    We do not publish a universal number. Performance depends on the hood design, the room and the exhaust system. Your EHS team and the hood manufacturer set operating criteria and the verification method for your installation.
    Can solvent be stored under the fume hood?
    A flammable storage base cabinet can hold daily-use solvent in appropriate containers, subject to fire code limits. Do not store containers inside the hood itself.
    Where should chromatography waste go?
    Into closed, labeled containers separated by waste stream, typically halogenated and non-halogenated. Keep the containers close to the hood during the run, and follow your institution’s hazardous waste program for pickup.
    Is this different from a general chemistry hood?
    The hood families are the same; the planning emphasis differs. Fraction handling spreads open solvent across the work surface and adds vertical, collector and waste considerations. See our chemistry hood page for broader bench-chemistry needs.

    Sources and related resources

    Technical references reviewed for this guide: OSHA 29 CFR 1910.1450 Appendix A (hood use, storage and ventilation recommendations), OSHA methylene chloride overview, and Prudent Practices in the Laboratory, chapter 9 (laboratory ventilation). Final requirements must be set by your EHS team, the hood manufacturer and the authority having jurisdiction. Related Labs USA pages: laboratory fume hoods, chemistry hood, polymer and resin prep hoods.

    Plan your chromatography hood around the real workload

    Share your solvent list and equipment dimensions and we will help organize the options.