Fume Hoods for Solvent Extraction & Sample Prep

A planning guide for environmental and analytical labs that run liquid-liquid extraction, Soxhlet extraction, extract concentration and standards preparation. Size the hood around the glassware, the solvents and the people who run the work every day.

Separatory funnel, Soxhlet extractor and volumetric flasks inside a laboratory fume hood

Shop Filtered Fume Hood Options Online

Important: many solvent extraction labs need a ducted fume hood, which we quote to your methods and building. These filtered (ductless) hoods are real catalog listings and are only suitable after the manufacturer reviews your exact solvent list, quantities and running hours. Prices are catalog starting prices.

Why extraction and sample prep deserve their own hood plan

Sample preparation is where most of the solvent in an environmental or analytical laboratory is actually handled. Water samples are shaken with an organic solvent in separatory funnels, soils and sediments are extracted for hours in Soxhlet apparatus, extracts are concentrated, and calibration standards are diluted and transferred all day. Each step releases vapor in a different way, and each puts a different demand on the hood: width for funnels, height for tall glassware, utilities for condensers and heating, and enough working depth for safe handling.

This guide is written for lab managers, QA leads, EHS staff and facility planners who are choosing laboratory fume hoods for an extraction or prep room. It focuses on the equipment and layout decisions that come before a quote. It does not replace your Chemical Hygiene Plan, the method you are validated to run or the review of a qualified ventilation engineer. If your project is mainly acid digestion, use our acid digestion and perchloric acid hood guide instead; for general chemistry teaching or research rooms, start with the chemistry hood overview.

Start with the method list.

The fastest way to an accurate hood specification is a list of the methods you run, the solvents in each, the typical batch size and how many extractions run at the same time. Everything on this page builds from that list.

Map each task to where the vapor is released

Extraction labs often describe their need as “a solvent hood,” but the tasks behave very differently. The table below summarizes common steps, using the U.S. EPA SW-846 extraction methods as reference points, and what each one means for the hood. Always follow the current version of the method your lab is accredited to perform.

TaskWhere vapor is releasedWhat it means for the hood
Separatory funnel liquid-liquid extraction (EPA Method 3510C)Venting the funnel after shaking. Method 3510C notes that methylene chloride builds pressure very quickly and that the funnel should be vented into a hood.Clear width for ring stands and funnels, room to shake and vent safely inside the sash opening, and a work surface that contains drips.
Continuous liquid-liquid extraction (EPA Method 3520C)Long-running extractors; the method describes extraction for 18 to 24 hours.Space that can stay occupied overnight, cooling water and power planned for unattended operation, and labeling of who owns the running setup.
Soxhlet extraction of solids (EPA Method 3540C)Heated solvent refluxing through a thimble with a condenser above.Interior height for the extractor and condenser, multiple heating positions if batches run in parallel, and condenser water supply and drain.
Kuderna-Danish concentrationHeated water bath and concentrator. The SW-846 methods state that the bath should be used in a hood.A level area for the bath, electrical receptacles placed per your electrical and safety review, and splash-resistant surfaces.
Pressurized fluid extraction (EPA Method 3545A)Instrument vent port during the gas purge step; the method says to follow the manufacturer’s directions for connecting it to a fume hood or other means.Coordinate instrument vent routing with the hood or exhaust design before the room layout is fixed.
Standards preparation and dilutionOpening stock solutions, pipetting and diluting in volumetric glassware.Usually lower volumes, but frequent. Consider a dedicated station so standards work is not displaced by long extractions.

Notice that very few of these steps are a single dramatic release. Most are repeated, short exposures at the same position, many times per shift. That pattern argues for a hood that is comfortable to work at and is not overcrowded, because overcrowded hoods tend to be worked with the sash too high and apparatus too close to the face opening.

Size the hood around the apparatus and the batch

Measure the setup, not the room

The interior of a hood fills quickly with ring stands, funnels, heating mantles, baths and waste containers. Lay the equipment for one realistic batch out on a bench, measure the footprint and the tallest assembly, and add room to work around it. That measurement is a better starting point than a catalog width picked by habit.

Long bench top fume hood with a wide working opening in a laboratory

Hood width is usually the decision that matters most in extraction rooms. Separatory funnel work spreads out sideways, and labs that run several samples at once need several funnel positions plus space for receiving flasks. Soxhlet and continuous extractors are tall rather than wide, so interior height and the sash travel you need to load them deserve attention. If both kinds of work happen in the same room, it is often cleaner to dedicate one hood to long-running extractors and keep another free for funnel work and concentration.

Width

Count funnel and extractor positions in a typical batch, then add room for receivers, a waste container and hand movement. Ask us to compare standard widths against that layout.

Height and sash

Measure the tallest assembly with its condenser. Confirm you can load and unload it without reaching over the top of the glassware or working with the sash fully open.

Depth

Apparatus should sit well inside the hood, not at the front edge. Confirm the usable depth with the actual equipment, including any bath or heater base.

Write down how many extractions run simultaneously and for how long. A hood that is fine for one daily batch may be overloaded when the lab adds a second shift or a new method. Planning one extra station during design is often far simpler than adding a hood to an operating lab later.

Ducted hood or filtered hood for solvent work?

Ducted is the common starting point

A ducted hood exhausts the captured air out of the building through a dedicated system. Extraction labs that handle mixtures of volatile organic solvents across many methods usually start here, because the hood does not depend on a filter being matched to every chemical in use.

Two ducted bench top fume hoods installed side by side on laboratory casework

Filtered, or ductless, hoods return air to the room after it passes through a filter. They can be appropriate for defined, lower-volume applications when the manufacturer has reviewed the exact chemical list, quantities and use pattern and has confirmed a suitable filter and monitoring arrangement. They are not a general substitute for a ducted hood. If anyone proposes a filtered hood for extraction work, send the full solvent and reagent list, typical volumes and running hours for that review before ordering. Our ducted vs. ductless fume hood guide and the ductless fume hood page explain the trade-offs in more detail.

For a ducted hood, the building side needs as much attention as the hood itself. Confirm who is responsible for the exhaust fan, the duct route, the roof discharge, the makeup air and the controls. Long-running extractors also raise a practical question: will the exhaust system run continuously, overnight and on weekends, while those extractors are operating? Agree on that with the facility team early, and plan how the lab will know if exhaust is lost. An airflow monitor gives users a visible indication at the hood.

Under OSHA’s laboratory standard, 29 CFR 1910.1450, an employer’s Chemical Hygiene Plan must include a requirement that fume hoods and other protective equipment are functioning properly and specific measures to ensure their performance. Build commissioning and periodic verification into the project scope, rather than treating them as an afterthought.

Liners, work surfaces and services

Look inside, where the work happens

Interior liners, the work surface, service fixtures and the sash all see solvent contact. Ask for the material of each wetted component and compare it against your solvent list and any acids used in the same hood. Contained, dished work surfaces help keep spills inside the hood rather than on the floor.

Fume hood interior with service fixture valves on the side wall and a lattice rod frame

Extraction labs rarely use solvents alone. Samples are acidified or made basic before extraction, sodium sulfate is used to dry extracts, and the same hood may be used for cleanup steps. Choose liner and work surface materials for the full chemical list, not only the main extraction solvent. If strong acid digestion is planned in the same room, that work belongs in a hood designed for it; see the acid digestion guide linked above.

ServiceWhy extraction labs need itQuestion to answer before quoting
Cold water and drainCondensers on Soxhlet, continuous extractors and concentration apparatus.How many condensers run at once, and is a recirculating chiller preferred over tap water?
Electrical receptaclesHeating mantles, water baths, stirrers and instrument controllers.How many devices per hood, and where should receptacles be located based on your electrical and safety review?
Vacuum or inert gasFiltration, evaporation or blanketing steps used by some methods.Which methods need it, and is it supplied centrally or by local equipment?
Lighting and visibilityReading meniscus lines and phase boundaries in funnels.Is the hood lighting adequate for phase separation work, and is the sash glass clear of obstructions?

Heat sources deserve particular attention with flammable solvents. Review the ignition sources inside and near the hood with your safety team and the equipment manufacturers, and document which heating devices are approved for use in each hood.

Standards preparation and derivatization stations

Small volumes, many repetitions

Analytical standards and derivatization steps typically involve small volumes, but they are repeated many times and require care and concentration. A dedicated, uncluttered station near the balance and standards storage reduces handling, keeps traceable work separate from bulk extractions and lowers the temptation to work outside a hood when the main hood is busy.

Building calibration solutions or treating small analytical aliquots calls for a more specific station review. See our analytical standards preparation and derivatization fume hood planning guide for balance separation, vial handling, reagent compatibility and the limits of filtered containment.

Bench top chemical fume hood with the sash lowered in a laboratory

Derivatization reagents can be reactive, moisture sensitive or toxic. The SDS for each reagent and the method’s safety section should drive where and how that work is done. If the lab uses a reagent that your Chemical Hygiene Plan classifies as particularly hazardous, OSHA’s laboratory standard calls for considering a designated area and containment devices such as fume hoods or glove boxes. Plan that station and its signage with your Chemical Hygiene Officer.

Weighing neat standards can be sensitive to airflow. Some labs weigh in a separate enclosure designed for balances and only open and dilute stocks in the hood. Discuss your weighing workflow with us so the plan does not force analysts into an awkward compromise.

Lay out the prep room as one workflow

Keep solvent storage close but separate

Extraction labs move a lot of solvent from storage to the hood and from the hood to waste. Approved flammable storage near the prep area shortens those trips. Confirm cabinet type, location, quantity limits and venting requirements with your fire code official and EHS team.

Open flammable storage cabinet with labeled solvent bottles and safety cans (illustration)

A good extraction room layout follows the sample: receiving and log-in, pH adjustment, extraction, drying and concentration, then transfer of the final extract to the instrument lab. Place hoods away from doors, busy aisles and supply-air outlets that can disturb airflow at the face. Leave clear floor space in front of each hood so an analyst is not working with people constantly passing behind them.

  • Waste: plan where spent solvent and aqueous waste are collected, labeled and stored, and how containers leave the room.
  • Glassware: locate washing and drying near the prep area so funnels and extractors are not carried across the lab.
  • Emergency equipment: confirm eyewash and safety shower locations, spill supplies and fire extinguisher placement with your safety team.
  • Casework: chemical resistant work surfaces and cabinets around the hoods carry the overflow of daily work; see our environmental testing lab furniture page.

Snorkels support, not replace, the hood

Some prep benches have short, low-volume steps near an open vessel. A source-capture exhaust arm can help there, but it is not an enclosure. Keep extractions, solvent venting and concentration inside the hood, and treat any snorkel as an addition for tasks your safety review has approved for it. See exhaust snorkels for options.

Laboratory with a bench top fume hood in front and an articulated exhaust arm over a bench behind it

Related environmental testing projects, and what they show

Labs USA has supplied equipment to environmental testing laboratories, and two published project pages are relevant here. We are careful about what they establish. Our CRM shows Closed Won orders for both customers, but neither project documents the customer’s extraction methods, solvent list, Soxhlet setups or the performance of installed systems, so this page does not claim them.

Pace Analytical, Oakdale, Minnesota

Documented scope: one polypropylene extraction arm with a manual damper, a wall bracket with top exhaust, a ten inch capture hood and a mounting plate, for a single bench station where the captured air is acidic. It shows a source-capture addition at one bench, not a fume hood or an extraction-room design. Read the Pace Analytical project.

Illustration of a round metal extraction hood on a flexible arm above an open beaker

Mostardi Platt, Pittsburgh and Austin

Documented scope: matching renovation packages for two laboratories, including steel casework, epoxy resin work surfaces and sinks, a bench mounted chemical fume hood and safety fittings. It shows how one hood and furniture specification was coordinated across two sites. It does not document which sample preparation methods are run in that hood. Read the Mostardi Platt project.

Illustration of a bench mounted chemical fume hood with a vertical rising sash

The images in this section are illustrations used on those project pages, not photographs of the delivered equipment. The useful lesson for a new extraction lab is practical: multi-site labs benefit from one consistent hood and work surface specification, and single bench additions should be scoped as exactly what they are.

Operating the hood day to day

Good habits protect the investment

Work at least several inches inside the face, keep the sash as low as the task allows, and avoid using the hood as solvent storage. Bottles and boxes left inside block airflow paths and reduce the room available for the next batch. Agree on these rules as part of training when the new hood is commissioned.

Bench top fume hood with a clear vertical sash above blue laboratory base cabinets

Before a run

Confirm the hood is operating and the monitor shows normal status, clear unneeded items, check glassware for cracks and confirm condenser water is flowing.

During long extractions

Label running setups with the analyst, method and start time. Agree on what happens if exhaust or cooling water is lost overnight.

Verification

Follow your Chemical Hygiene Plan for hood performance checks and keep records. Re-verify after changes to the room, the exhaust system or the hood.

OSHA’s laboratory standard requires employers to provide training and information about the hazards of chemicals in the work area and the measures that protect employees, including work practices and emergency procedures. Hood use is a natural part of that training for every analyst who runs extractions.

What to send for an extraction hood quote

Share as much of the following as you can. If something is unknown, list it as an open question; we will not fill gaps with assumptions.

  • Methods: the extraction, concentration and standards methods you run, with typical batch sizes and how many run at the same time.
  • Chemicals: solvent and reagent list, including acids, bases and derivatization reagents, with SDSs available.
  • Apparatus: footprint of a typical batch, the tallest assembly with its condenser, and any instruments that need a vent connection.
  • Room: a dimensioned sketch with doors, aisles, supply-air outlets, existing casework and storage.
  • Building: existing exhaust capacity information, roof access, and who manages HVAC and controls.
  • Services: water, drain, electrical, vacuum or gas needs per hood.
  • Project: schedule, whether the lab stays in operation during work, installation and commissioning responsibilities.

Related planning resources

Technical references used for this guide

Method details were checked against the primary documents below. Always use the current version of the method you are accredited to run and your own Chemical Hygiene Plan.

Where the same laboratory also develops solvent-containing formulations, review polymer, resin and adhesive preparation hood planning as a separate application. A sample-extraction setup does not establish suitability for a curing reaction or a different formulation.

When extraction glassware is solvent-rinsed before washing, plan vessel clearance, compatible trays and closed rinse collection separately with our guide to glassware solvent-cleaning hood planning. Review the exact apparatus, chemicals and exhaust requirements before selecting or sharing an enclosure.

Plan your extraction and sample prep hood

Send your method list, solvent list and a room sketch. We will help you compare hood sizes, ducted and filtered options, materials and services, and separate equipment from project scope in the quote.

    For a shared chemical-handling station, review solvent dispensing and reagent preparation fume hood planning to account for source bottles, receiving vessels, compatible spill trays and closed waste before selecting the work-zone layout.

    What size fume hood do I need for liquid-liquid extraction?
    Size it from your batch. Lay out the funnels, ring stands, receivers and waste container for a typical run, measure the footprint and add working room. Labs that run several funnels at once usually need more width than a single-analyst research hood.
    Can Soxhlet extraction run in a standard bench top hood?
    Often it can, but check the interior height and sash travel against the tallest extractor and condenser, and plan cooling water, drain and electrical service for each heating position. Long runs also need an agreement on continuous exhaust operation.
    Is a ductless fume hood acceptable for solvent extraction?
    Only if the manufacturer has reviewed your exact chemical list, quantities and running hours and confirmed a suitable filter and monitoring arrangement. Many extraction labs use mixed volatile solvents and choose ducted hoods. Make the decision with your EHS team.
    Should standards preparation share a hood with extractions?
    It can, but a dedicated station often works better. Standards work is frequent and precise, and it is easily displaced by long-running extractions. A separate station also keeps traceable work organized.
    Do I need a separate hood for acid digestion?
    If your lab performs significant acid digestion, use a hood specified for that work. Our acid digestion and perchloric acid hood guide covers those requirements; this page focuses on organic solvent extraction and prep.
    Do your environmental testing projects prove a particular setup works?
    No. The Pace Analytical and Mostardi Platt projects document the equipment supplied in their stated scope. They do not document the customers’ extraction methods or system performance, and we do not present them as evidence for a specific extraction setup.
    What information speeds up a quote?
    Your method list, chemical list, batch sizes, number of simultaneous runs, a room sketch and any existing exhaust information. Unknowns are fine; list them as questions.

    Build the hood plan around your methods

    Start with the extraction, concentration and standards work your lab actually runs.

    Get a Free QuoteCall Now: (801) 855-8560